Gate Repair in Pasadena - Same-Day Repair, Priced Before We Start

Trusted Gate Repair for Pasadena Homeowners

Gate repair in Pasadena typically costs $180 to $340 for most common fixes like hinge realignment, opener troubleshooting, or track adjustment. Weld repairs and full motor replacements can run higher, usually $400 to $900. Same-day service is available throughout Pasadena, Altadena, and San Marino when you call before noon.

Call (626) 657-5425

Warden Gate Repair has served Pasadena homeowners since 2008. Led by Cole Rafferty, our team is factory-trained on LiftMaster, FAAC, BFT, and Linear systems. We answer the phone 24/7, and every visit starts with a written price before any work begins. Call (626) 657-5425 for a free estimate.

Driveway Gate Repair

Driveway Gate Repair covers the gate that guards your curb: the leaf or panel that slides or swings across your driveway entrance, plus its track, hinges, wheels, and opener. In Pasadena, driveway gates take a beating from summer heat and the clay-heavy soil that shifts with every wet winter, throwing posts out of plumb and creating the need for Gate Realignment. Repair work usually runs $200 to $380, depending on whether we’re fixing hardware or the gate motor itself.

Misaligned Track and Roller Work

When a sliding driveway gate grinds or stalls halfway, the track has usually shifted or a roller has worn flat. We straighten the rail, replace rollers, and set the gate back on its travel line.

Post Reset and Hinge Replacement

Shifting soil around Pasadena’s hillside streets pushes posts and stresses hinges. We reset posts in concrete, swap bent hinges, and re-square the leaf so it closes against the stop without dragging. Our Hinge & Post Repair service handles these exact problems.

Gate Welding

Gate Welding is the structural repair of cracked, broken, or rusted metal on iron, steel, and aluminum gates. You need it when a hinge tears loose, a bottom rail splits, or a decorative finial snaps off. We carry a mobile welder on the truck, so most weld repairs happen in one visit. Expect $250 to $600 for most weld jobs in Pasadena, depending on the extent of the damage.

Cracked Frame and Rail Repair

A crack in the top or bottom rail weakens the whole gate. We grind the crack, weld it solid, and reinforce the back side so the gate doesn’t flex at the weak point again.

Hinge and Post Welding

When a hinge tears free from the gate or post, bolting it back isn’t enough. We weld the hinge or its plate back, then realign the gate so it hangs true and swings without fighting the frame.

Commercial Gate Repair

Commercial Gate Repair covers gates at apartment complexes, office buildings, parking garages, and industrial yards across Pasadena and the San Gabriel Valley. These gates run harder than residential ones, often cycling hundreds of times a day. We service LiftMaster and DoorKing commercial operators, replace damaged sections, and weld broken structural members. Repair costs range from $350 to $900, with written pricing before work starts.

Access Gate and Operator Repair

When a commercial gate stops responding to call boxes, keypads, or remotes, the operator is usually the culprit. We diagnose the motor, limit switches, and loop detectors, then replace only what’s actually failed.

High-Cycle Structural Reinforcement

Apartment gates in Pasadena’s denser neighborhoods near Old Town see constant use, and that fatigue shows up as stress cracks at hinge points. We weld and reinforce those joints so the gate doesn’t fail during peak hours.

Iron Gate Repair

Iron Gate Repair addresses the specific wear patterns of solid iron and iron-tube driveway gates, the kind you see on Pasadena’s Spanish Revival and Craftsman homes. Iron is strong but heavy, and over time it sags, rusts at the base, and pulls away from hinges. Repair typically costs $250 to $550, depending on whether we’re welding cracks, replacing rusted sections, or resetting hinge posts.

Rust Removal and Section Replacement

Bottom rails on iron gates sit in standing water after Pasadena’s winter rains. We cut out rusted-through sections, weld in new steel, and prime and paint to match the existing finish.

Sag Correction and Hinge Rebuild

An iron gate that scrapes the driveway has sagged at the hinge line. We rebuild the hinge assemblies, shim and square the leaf, and make sure the Lock Repair releases without lifting.

Sliding Gate Repair

Sliding Gate Repair fixes the most common issue with Automatic Gate Repair in Pasadena: the gate that won’t slide smoothly, stops midway, or jumps its track. Sliding gates depend on clean rollers, a level rail, and a working motor to function. Repair visits run $220 to $400 for mechanical work, and motor repairs or replacements add $150 to $450 depending on the unit.

Track Cleaning and Roller Replacement

Leaves, gravel, and that fine Pasadena dust work into the track and chew up rollers. We clear the rail, replace worn rollers and guide wheels, and test the full travel cycle from both limits.

Opener Synchronization and Limit Set

When a sliding gate overtravels or reverses without reason, the limit settings or the receiver board are usually at fault. We recalibrate the travel and obstruction settings, then test the gate under load before we leave.

Wrought Iron Gate Repair

Wrought Iron Gate Repair restores the ornamental iron gates that front so many Pasadena driveways and garden entries. Wrought iron gates are custom-built, which means each repair needs to respect the original work. We weld broken scrolls, rebuild hinges, treat rust, and repaint damaged areas. Expect $300 to $700 for careful wrought iron restoration work.

Ornamental Scroll and Pickett Repair

Decorative scrolls and pickets snap at their thinest points, usually from impact or long-term vibration. We weld the break cleanly, smooth the weld, and apply rust-inhibiting primer before painting.

Hinge Rebuild on Historic Gates

Original hingework on wrought iron gates is often decades old and seized. We free the hinge, replace the pintle or strap as needed, and preserve the original look while restoring function.

Metal Gate Repair

Metal Gate Repair is the broad category for aluminum, steel, and tubular metal gates, including the powder-coated driveway gates popular in newer Pasadena developments. Metal gates dent, bend at the corners, and develop hinge play. Repair work runs $200 to $500, with aluminum often cheaper to fix than steel because it’s lighter to handle and easier to cut.

Dent Removal and Panel Straightening

A bumped metal gate leaf is a visual and mechanical problem. We straighten bent panels, reinforce dented corners with welded gussets, and restore the gate’s clean lines.

Latch and Lock Alignment

When a metal gate won’t latch, the strike has usually moved or the leaf has dropped. We re-hang the gate, align the latch, and test the release from both sides of the fence.

Wood Gate Repair

Wood Gate Repair covers the side gates, back gates, and driveway gates framed in redwood and cedar across Pasadena’s residential neighborhoods. Wood swells in winter, shrinks in summer, and that movement loosens hinges, warps stiles, and rots corners. Repairs range from $180 to $450, depending on whether we’re rebuilding the frame or just replacing hardware.

Frame Rebuilding and Joint Repair

The mortise-and-tenon joints on older wood gates eventually fail. We pull the gate, re-cut the joints, and reassemble the frame with weather-resistant fasteners so the gate is square again.

Hardware and Post Reinforcement

A wood gate that drags on the latch side has usually pulled its hinges out of a rotting stile. We repair or replace the stile, install longer hardware with proper backing, and treat any exposed wood.

Brands We Service

We’re factory-trained on LiftMaster gate operators, which means we know the difference between a failing logic board and a weak capacitor before we order parts. We stock LiftMaster OEM components on the truck, so most repairs finish in a single visit.

Our team also carries deep experience with FAAC and BFT swing gate motors, the two most common Italian-built operators in Pasadena’s hillside driveways. We diagnose FAAC hydraulic issues and BFT control board faults every week, and we carry the replacement parts to fix them on the spot. And for Linear operators still working across older Pasadena homes, we source original-equipment parts and can extend their life. Whether you have a LiftMaster, FAAC, BFT, Linear, or another make, we can help.

Signs You Need a Pro Right Now

• Your gate stops mid-cycle or reverses instantly. This usually means an obstruction sensor is misaligned or a limit switch has failed. A gate that won’t complete its travel cycle is also a gate that won’t keep anyone out.
• You hear grinding, squealing, or a loud click from the motor. Grinding points to gear wear inside the operator. Left alone, it strips the drive gear entirely and turns a $250 repair into a $700 replacement.
• The gate sags or drags on the driveway. Sagging means the hinge line is failing or the frame is cracking. Every day it scrapes, the weight is tearing the leaf further out of alignment.
• You see rust blooms or hairline cracks near the hinges. Rust at the base of an iron gate is structural, not cosmetic. Hairline cracks at hinges spread fast and can cause the gate to fall off its post entirely.
• The gate won’t respond to the remote, keypad, or call box. That points to the receiver board, the antenna, or the power supply. It might be a simple fix, but every cycle a non-responsive gate stays open, your property stays exposed.

Our Process, Step by Step

1. 1
   Call and talk to a real person. Our dispatch line is answered 24/7 by someone in our Pasadena office, not a recording service. We ask what your gate is doing, what brand it is, and when you want us there.
2. 2
   Get your technician’s name and photo before the visit. Before the truck rolls, we send you the tech’s name, photo, and background-check confirmation. That’s the Threshold Standard, and it’s non-negotiable.
3. 3
   On-site diagnosis and written quote. The tech walks the gate, tests the opener, finds the actual cause, and writes the price down on paper. You see the number and agree to it before a single part gets unboxed.
4. 4
   Repair, test, and clean up. We fix the gate, cycle it ten to fifteen times under normal load, adjust the limits, and make sure the path is clear. We leave the work area the way we found it.
5. 5
   365-Day Done Right Promise. Every repair is guaranteed in writing for a full year. If something we fixed fails, the return visit and the re-repair are free. No fine print.

How Much Does Gate Repair Cost in Pasadena?

Our Service Area Near Pasadena

Warden Gate Repair is based in Pasadena and serves the surrounding communities: Altadena, San Marino, South Pasadena, Alhambra, Monterey Park, Rosemead, Temple City, Tujunga, Monrovia, and Baldwin Park. Most calls within Pasadena see a technician within 24 hours, and emergency repair requests before noon usually get same-day service. We also run dedicated pages for our work in Gate Repair in Glendale and Gate Repair in El Monte.

Frequently Asked Questions About Gate Repair in Pasadena

Schedule Your Gate Repair Service in Pasadena Today

If your gate is sagging, stuck, or making noise, call (626) 657-5425 now. We’ll answer live, ask what’s happening, and schedule a time that works. You’ll get a written price before any work starts, and the job is covered by our 365-Day Done Right Promise.

Written by Cole Rafferty, Owner at Warden Gate Repair Pasadena, serving Pasadena since 2008.