Ghost Controls Keypad & Intercom Repair Nationwide

Ghost Controls Keypad & Intercom Repair: The Pasadena Owner’s Guide

Ghost Controls keypad and intercom repair in Pasadena typically runs $185 to $420 installed, depending on whether we’re replacing the keypad head, the intercom board, or the full entry station. Most jobs we complete same-day when we have the part on the truck, which we usually do for the common Ghost Controls models. You’ll know this part has failed when the keypad stops waking up, certain keys quit registering, or the voice intercom turns into a wall of static right as your delivery driver is asking how to get in.

Call (626) 657-5425

Here’s the picture we see most often: the gate still opens from inside the house or from a remote, but the outside keypad is dead or half-dead. That points squarely at the entry station, not the gate operator itself. The fix is usually a clean swap, and we quote the exact number before we unscrew the first housing.

Which Ghost Controls Models This Applies To

We service keypads and intercoms across the Ghost Controls line, including the AXDP, TDS2XP, and the newer TSS1 series entry systems. If you’re not sure which one you have, open the keypad housing and look for a sticker with a part number that usually starts with “AX” or “TSS.” That number matters more than the gate opener model, because Ghost Controls has quietly changed keypad connectors over the years. A keypad from a 2017 TDS2XP will not plug into a 2021 TSS1 control board without an adapter harness, and that harness is not something most Pasadena hardware stores carry.

Warden Gate Repair Pasadena is an independent service provider. We’re not affiliated with Ghost Controls, but we stock OEM keypads and intercom modules for the series above, plus quality aftermarket equivalents where they make sense. In our experience, the OEM Ghost Controls keypad is worth the extra $40 or so for the wire-in models because the aftermarket rubber keypad membranes tend to crack in Pasadena’s dry summer heat within two to three years. We’ll tell you which side of that trade-off fits your gate before you spend a dollar.

Signs Your Ghost Controls Keypad & Intercom Is Failing

• Keypad lights up but won’t accept your code. This is usually a worn membrane under the keys or a failing edge connector inside the housing – not a programming issue. Reprogramming won’t fix it if the tactile switch under the “3” key has physically failed.
• Some keys work, others don’t. The carbon contacts under individual keys wear unevenly. If your code contains a “5” or “7” and neither registers, that’s the tell. The board is still good, but the keypad pad itself is done.
• Intercom audio is one-way or full of popping. On Ghost Controls intercom modules, the electrolytic capacitors on the audio board degrade over time, especially with Pasadena’s temperature swings from cold foothill mornings to 95-degree afternoons. We get the same complaint on systems near the Arroyo where morning fog adds moisture.
• Keypad works but the gate ignores it. This points to the relay output on the keypad board or the wiring between the entry station and the gate control board. We trace it with a meter before declaring anything dead, because sometimes it’s just a corroded spade connector.
• The housing is cracked or full of ants. Ghost Controls keypads are decent plastic, but years of direct sun and the occasional weed-whacker hit take their toll. Ants love the warmth inside the housing and their bodies short the low-voltage contacts. We see this constantly on older Pasadena properties with mature landscaping.

Replacement Cost & What’s Included

Here’s the honest Pasadena price picture for Ghost Controls keypad and intercom work:

• Keypad-only replacement (AXDP or similar): $185 to $260 installed
• Keypad with new wiring run to the control board: $260 to $340 installed
• Full entry station with intercom (TSS1 style): $340 to $420 installed
• Intercom board repair (component-level): $120 to $180

The range comes down to how far the keypad sits from the gate control board, whether the existing wire is still good, and which Ghost Controls series you have. Every quote is written and agreed before work starts. No surprise line items at the end. The labor includes testing the whole entry loop – keypad, intercom, gate response – not just the part we replaced. And every repair carries the 365-Day Done Right Promise: if it fails within a year, the return visit is free, in writing.

DIY or Call Us?

These are low-voltage systems, so the electrical danger is minimal. The real risk is buying a keypad that doesn’t match your Ghost Controls series and then cutting into the wiring to make it fit. We’ve repaired more than one gate where an owner spliced an aftermarket keypad with wire nuts and electrical tape, and Pasadena’s dry season turned that splice into a corrosion point within months.

What you can safely check: confirm the keypad has power (does anything light up?), listen for weak audio, and look for visible cracks or ant trails. That’s useful information to give us on the phone. What you shouldn’t do is start swapping boards or re-terminating wiring unless you’re comfortable with a multimeter and low-voltage wiring standards. If not, call (626) 657-5425. We’ll tell you over the phone what it likely is, what it costs to fix, and when we can be there.

FAQs